What is a Environmentally friendly tubular quenching furnace? heating furnace specifications, models, and parameters

Environmentally friendly tubular quenching furnaceIt is an efficient, energy-saving and environment-friendly metal heating device.，The price is low and affordable，modern technology。The following is to introduce the Environmentally friendly tubular quenching furnace:

1、Brief introduction of Environmentally friendly tubular quenching furnace

Environmentally friendly tubular quenching furnaceIt is a kind of equipment which uses gas as fuel and is specially used for heating metal before forging.。

Environmentally friendly tubular quenching furnace

2、Environmentally friendly tubular quenching furnace characteristics

The Environmentally friendly tubular quenching furnace features are as follows:

1. Efficient heating

The Environmentally friendly tubular quenching furnace can heat the metal to the required forging temperature in a very short time, reducing the loss caused by the oxidation of the metal.

2. Easy to control

By adjusting the burner and ventilation system, the temperature and atmosphere in the furnace can be accurately controlled to meet the heating requirements of different metal materials.

3. energy saving and environmental protection

Natural gas is a kind of clean energy, which produces less waste gas and waste smoke after combustion and has little environmental pollution. At the same time, through wall regenerative combustion technology, flue gas waste heat recovery system and other technical means, the Environmentally friendly tubular quenching furnace further improves energy utilization efficiency and reduces energy consumption and emissions.

4. Easy to maintain

The structural design of the Environmentally friendly tubular quenching furnace is reasonable and easy to maintain, which reduces the operating cost and failure rate of the equipment.

5. Easy to control

The combustion system and ventilation system of the Environmentally friendly tubular quenching furnace can be adjusted as required to accurately control the temperature and atmosphere in the furnace and meet the heating requirements of different metal materials.

Environmentally friendly tubular quenching furnace

3、Structural characteristics of Environmentally friendly tubular quenching furnace

The Environmentally friendly tubular quenching furnace structure is introduced as follows:

1. Radiation chamber

The heat load of the main place for Environmentally friendly tubular quenching furnace heat exchange accounts for about 70%-80% of the whole furnace. The furnace tube in the radiation room conducts heat through flame or high-temperature flue gas, which is mainly radiant heat, so it is called radiation tube.

2. Waste heat recovery system

Used to recover the exhaust heat of the heating furnace. There are two kinds of recovery methods, one is to recover by preheating combustion air, so that the recovered heat can return to the furnace again; The other is to use another recovery system to recover heat. The former is called air preheating mode, and the latter is usually called waste heat boiler mode.

3. ventilation system

Ensure the gas flow in the furnace and maintain the stability of the atmosphere and temperature in the furnace.

4. convection chamber

The material is heated by convection heat transfer of high temperature flue gas discharged from the radiation chamber. Flue gas washes the tube wall of the furnace tube at a high speed to carry out effective convection heat transfer, and its heat load accounts for about 20%-30% of the whole furnace. The convection chamber is generally arranged above the radiation chamber, and some are placed on the ground alone. In order to improve the heat transfer effect, nail head tubes or finned tubes are often used in furnace tubes.

5. Waste heat recovery system

Used to recover the exhaust heat of the heating furnace. There are two kinds of recovery methods, one is to recover by preheating combustion air, so that the recovered heat can return to the furnace again; The other is to use another recovery system to recover heat. The former is called air preheating mode, and the latter is usually called waste heat boiler mode.

Environmentally friendly tubular quenching furnace

4、Environmentally friendly tubular quenching furnace use

The purpose of Environmentally friendly tubular quenching furnace is introduced as follows:

1. Metal forging heating

The Environmentally friendly tubular quenching furnace can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

2. Metal heat treatment

In addition to forging heating, Environmentally friendly tubular quenching furnaces can also be used for metal heat treatment processes, such as annealing and tempering. These processes can improve the microstructure and properties of metal materials, and improve their service life and mechanical properties.

3. Metal tempering

By properly heating and cooling the metal material, the Environmentally friendly tubular quenching furnace can realize the quenching and tempering treatment of the metal. This is helpful to adjust the hardness and toughness of metal to meet the needs of different workpieces.

4. Energy conservation and environmental protection

The Environmentally friendly tubular quenching furnace uses clean energy as fuel, which has lower emissions and higher energy efficiency than traditional coal-fired or oil-fired stoves. This is helpful to reduce environmental pollution and realize green production.

5. Metal forging heating

The Environmentally friendly tubular quenching furnace can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

Environmentally friendly tubular quenching furnace

5、Environmentally friendly tubular quenching furnace function

Environmentally friendly tubular quenching furnaceit has the functions of temper, hardening and tempering, heat treatment, quench and normalizing，it has the characteristics of energy saving and environmental protection, Strong adaptability, energy-efficient, energy saving and environmental protection and Easy to control，it is an ideal choice for customers to buy Environmentally friendly tubular quenching furnace。

Environmentally friendly tubular quenching furnace

6、Environmentally friendly tubular quenching furnace price

The Environmentally friendly tubular quenching furnace price is introduced as follows:

1. geographical position

Geographical location also has a certain influence on the formulation of price, because there is a close relationship between geographical location and transportation cost. Generally, the price of places with superior geographical location will be more fair, which is lower than that of those remote cities. One-combustion energy saving address:Jinan, Shandong province, where the traffic is very developed and convenient, provides a series of conveniences for the distribution of products to a great extent.

2. product function

The more functions a product has, the higher its manufacturing cost, so that the product can be used by customers as much as possible, which can create more useful value for customers, so the price will be higher.

3. market demand

Generally, when the supply of Environmentally friendly tubular quenching furnace exceeds the demand in the market, the product price will naturally decrease, on the contrary, the product price will increase.

4. Product configuration difference

There is a direct connection between configuration and specifications. Generally speaking, with different specifications, its configuration scheme will be different, and the selection of products' materials and parts will be different, so the sales price of products will be different. It is not difficult to see that the configuration and price of Environmentally friendly tubular quenching furnace are closely related. One-combustion energy saving has comprehensively measured the configuration and sales price of products when designing Environmentally friendly tubular quenching furnace, which not only ensures that the functions of products can meet the actual needs of customers, but also can be in terms of price.

5. Product technology

Each customer needs different products, wants to achieve different purposes, and has different product technical design. The higher or more advanced the technical requirements, the more the product cost will be, and the price will increase with the increase of cost. On the contrary, the price will be cheaper.

Environmentally friendly tubular quenching furnace

Environmentally friendly tubular quenching furnacemultifunctional, with functions such as hardening and tempering, quench, Casting heating, Forging heating and temper，It is an important heating equipment before metal forging. It uses natural gas as fuel to heat metal materials through high-temperature flame and smoke generated by combustion to meet the requirements of forging process.，the product looks atmospheric.。