Introduction to High temperature and low dust SCR denitrification, SCR denitration specifications, model parameters

High temperature and low dust SCR denitrificationis an efficient, stable and environment-friendly flue gas denitrification technology.，the principle is simple.Under the action of catalyst, reducing agents (such as ammonia, urea, etc.) react with nitrogen oxides in flue gas to convert them into harmless nitrogen and water vapor.，Intelligent control is gradually realized. By integrating advanced control system and sensor technology, the High temperature and low dust SCR denitrification can monitor the composition and emission concentration of flue gas in real time, and automatically adjust the injection amount of reductant and the active state of catalyst to ensure the stability and reliability of denitrification efficiency.、It is famous for its high-efficiency denitration ability, which can usually reach more than 90% denitration efficiency. This means that the High temperature and low dust SCR denitrification technology can significantly reduce the concentration of nitrogen oxides (NOx) in flue gas and make it meet strict environmental protection emission standards. This high-efficiency denitration ability is mainly due to the promotion of the catalyst, which makes the chemical reaction between reductant and NOx more rapid and thorough.、Technology has been developed and applied for many years, and it is mature and stable. The High temperature and low dust SCR denitrification has high reliability and stability, and can maintain stable denitrification efficiency under various working conditions. In addition, the High temperature and low dust SCR denitrification technology has good adaptability and adjustability, and can be adjusted and optimized according to different flue gas components and emission requirements.、The by-products produced by the technology are mainly nitrogen and water vapor, which are harmless to the environment and will not cause secondary pollution. Compared with the traditional wet flue gas denitrification technology, the High temperature and low dust SCR denitrification technology does not need to use a lot of water resources and will not produce pollutants such as wastewater, which is more in line with the requirements of environmental protection and sustainable development.、The initial investment of technology may be high, but in the long run, its economic feasibility is remarkable. The high-efficiency denitration ability of High temperature and low dust SCR denitrification technology can significantly reduce the environmental emission cost of enterprises and avoid fines and legal risks due to illegal emissions. In addition, High temperature and low dust SCR denitrification technology can also reduce operating costs and improve the economic benefits of enterprises by recycling heat energy.，It has a wide range of uses, and is often used inPromote sustainable development,environmental protection,Meet the requirements of environmental protection,Improve product quality,Flue gas denitrification and so on，Commonly used inPromote sustainable development,environmental protection,Improve product quality,Meet the requirements of environmental protection,Flue gas denitrification and so on。

1、Brief introduction of High temperature and low dust SCR denitrification

High temperature and low dust SCR denitrificationit refers to the process of removing nitrogen oxides from flue gas to reduce environmental pollution. NOx is a pollutant harmful to the atmospheric environment, which has strong irritation and toxicity, and will lead to environmental problems such as acid rain and photochemical smog, and also endanger human health. The main principle of flue gas denitrification technology is to reduce NOx to nitrogen and water by adding appropriate reducing agent or catalyst in the combustion process or flue gas treatment system, so as to reduce NOx emission.，is carefully developed by One-combustion energy saving combined with advanced technology。

High temperature and low dust SCR denitrification

2、High temperature and low dust SCR denitrification function

High temperature and low dust SCR denitrificationmultifunctional, with functions such as Improve energy efficiency, environmental protection, Improve working conditions, environmental protection and Improve energy efficiency，is a kind of high quality and low price High temperature and low dust SCR denitrification，the main structure includes Temperature control and monitoring system, control system, Catalyst supply system, Flue gas mixing and distribution system and Catalyst reactor，It has the functions of Promote sustainable development, Flue gas denitrification, Improve product quality, Meet the requirements of environmental protection and environmental protection，it is an ideal choice for customers to buy High temperature and low dust SCR denitrification。

High temperature and low dust SCR denitrification

3、High temperature and low dust SCR denitrification explanation video

The following is the live video of High temperature and low dust SCR denitrification designed and produced by One-combustion energy saving for users, from which we can see the the advantage is The technology is suitable for many industries and processes, such as coal-fired power plants, iron and steel smelting, cement production and so on. These industries will produce a large number of NOx emissions in the production process, and the High temperature and low dust SCR denitrification technology can provide effective denitrification solutions for them. In addition, the gate technology can be adjusted and optimized according to different flue gas components and emission requirements to meet different denitration requirements.、There are many kinds of catalysts used in the technology, including vanadium-based catalysts and titanium-based catalysts, which can promote the chemical reaction between reductant and NOx at a lower temperature. At the same time, the active components and carrier materials of the catalyst are constantly being developed and improved to improve its catalytic efficiency and service life. This enables the High temperature and low dust SCR denitrification technology to maintain efficient denitrification capability in a wider temperature range and more complex flue gas conditions.、Intelligent control is gradually realized. By integrating advanced control system and sensor technology, the High temperature and low dust SCR denitrification can monitor the composition and emission concentration of flue gas in real time, and automatically adjust the injection amount of reductant and the active state of catalyst to ensure the stability and reliability of denitrification efficiency.、The by-products produced by the technology are mainly nitrogen and water vapor, which are harmless to the environment and will not cause secondary pollution. Compared with the traditional wet flue gas denitrification technology, the High temperature and low dust SCR denitrification technology does not need to use a lot of water resources and will not produce pollutants such as wastewater, which is more in line with the requirements of environmental protection and sustainable development.、The initial investment of technology may be high, but in the long run, its economic feasibility is remarkable. The high-efficiency denitration ability of High temperature and low dust SCR denitrification technology can significantly reduce the environmental emission cost of enterprises and avoid fines and legal risks due to illegal emissions. In addition, High temperature and low dust SCR denitrification technology can also reduce operating costs and improve the economic benefits of enterprises by recycling heat energy. of One-combustion energy savingHigh temperature and low dust SCR denitrification.。

High temperature and low dust SCR denitrification

As you can see from the live video.，One-combustion energy saving is a High temperature and low dust SCR denitrification。

4、Introduction of High temperature and low dust SCR denitrification characteristics

High temperature and low dust SCR denitrification has the following characteristics

1. Environmental protection

The final products of High temperature and low dust SCR denitrification technology are harmless nitrogen and water vapor, which will not cause secondary pollution to the environment.

2. High denitration efficiency

The denitration efficiency of High temperature and low dust SCR denitrification technology can reach more than 90%, and it is a widely used post-combustion denitration technology at present.

3. selectivity

Under the action of catalyst, the reducing agent mainly reacts with NOx selectively, but less with other components (such as oxygen) in flue gas, thus reducing unnecessary consumption.

4. Mature technology

After years of development and application, High temperature and low dust SCR denitrification technology is very mature and has a wide application prospect.

5. Environmental protection

The final products of High temperature and low dust SCR denitrification technology are harmless nitrogen and water vapor, which will not cause secondary pollution to the environment.

High temperature and low dust SCR denitrification

5、High temperature and low dust SCR denitrification price advantage

The High temperature and low dust SCR denitrification price is introduced as follows:

1. cost of production

If the cost of the product is high, the selling price of the product will be high, so the cost input is an important factor that causes the price change of the High temperature and low dust SCR denitrification.

2. market demand

Generally, when the supply of High temperature and low dust SCR denitrification exceeds the demand in the market, the product price will naturally decrease, on the contrary, the product price will increase.

3. brand

Different brands of products in the same series have more or less differences in product prices, and different brands of High temperature and low dust SCR denitrification have more or less differences in price.

4. Product technology

The more advanced the technology, the higher the price will be, otherwise the product price will be low, and customers must pay attention to whether their own technology meets the production requirements when purchasing products.

5. product function

The more functions a product has, the higher its manufacturing cost, so that the product can be used by customers as much as possible, which can create more useful value for customers, so the price will be higher.

High temperature and low dust SCR denitrification

6、One-combustion energy saving company service

Customers should not only consider quality, performance and price factors when purchasing High temperature and low dust SCR denitrification, but also consider the after-sales service of manufacturers. Good after-sales service can reduce many unnecessary troubles for customers. One-combustion energy saving Factory always adheres to the service attitude of "customer is God", implements high-standard and high-quality after-sales service attitude, conducts regular customer satisfaction surveys, and strictly supervises the quality of after-sales service, so as to relieve customers' purchasing concerns and make purchasing customers completely worry-free.。

One-combustion energy saving

High temperature and low dust SCR denitrificationat work,Catalysts are used to promote the selective catalytic reduction reaction between reducing agents (such as ammonia and urea) and NOx in flue gas. Under the action of catalyst, the reductant preferentially reacts with NOx to generate harmless nitrogen and water vapor, but hardly reacts with oxygen in flue gas. This chemical reaction is usually carried out in the temperature range of 200-450℃, and the specific reaction temperature depends on the type of catalyst selected.，It is famous for its high-efficiency denitration ability, which can usually reach more than 90% denitration efficiency. This means that the High temperature and low dust SCR denitrification technology can significantly reduce the concentration of nitrogen oxides (NOx) in flue gas and make it meet strict environmental protection emission standards. This high-efficiency denitration ability is mainly due to the promotion of the catalyst, which makes the chemical reaction between reductant and NOx more rapid and thorough.、There are many kinds of catalysts used in the technology, including vanadium-based catalysts and titanium-based catalysts, which can promote the chemical reaction between reductant and NOx at a lower temperature. At the same time, the active components and carrier materials of the catalyst are constantly being developed and improved to improve its catalytic efficiency and service life. This enables the High temperature and low dust SCR denitrification technology to maintain efficient denitrification capability in a wider temperature range and more complex flue gas conditions.、Technology has been developed and applied for many years, and it is mature and stable. The High temperature and low dust SCR denitrification has high reliability and stability, and can maintain stable denitrification efficiency under various working conditions. In addition, the High temperature and low dust SCR denitrification technology has good adaptability and adjustability, and can be adjusted and optimized according to different flue gas components and emission requirements.、The technology is suitable for many industries and processes, such as coal-fired power plants, iron and steel smelting, cement production and so on. These industries will produce a large number of NOx emissions in the production process, and the High temperature and low dust SCR denitrification technology can provide effective denitrification solutions for them. In addition, the gate technology can be adjusted and optimized according to different flue gas components and emission requirements to meet different denitration requirements.、Intelligent control is gradually realized. By integrating advanced control system and sensor technology, the High temperature and low dust SCR denitrification can monitor the composition and emission concentration of flue gas in real time, and automatically adjust the injection amount of reductant and the active state of catalyst to ensure the stability and reliability of denitrification efficiency.，the product looks beautiful.。