Introduction to High temperature bright well annealing furnace, introduction to heating furnace advantages and characteristics

High temperature bright well annealing furnaceIt is a forging heating device using gas as fuel.，the principle is simple.The high-temperature flame and flue gas generated when the fuel burns in the furnace are used as heat sources to heat the medium flowing in the tube to reach the specified process temperature. Fuel is ejected from the burner and burned, resulting in high-temperature flame and high-temperature flue gas. The high-temperature flame transfers heat to the furnace tube in the radiation chamber through radiation, and then to the medium in the furnace tube. The high-temperature flue gas enters the convection chamber of the heating furnace upward due to the suction force of the chimney or the action of the induced draft fan, and the heat is transferred to the furnace tube in the convection chamber by convection, and then to the medium in the furnace tube.，the advantage is The use of clean and environmentally friendly natural gas as fuel effectively avoids the adverse effects of chemical reactions between impurities such as coal-fired furnaces and forgings during heating. At the same time, natural gas has high calorific value and high combustion temperature, and the combustion temperature can be further increased by preheating air and fuel. In addition, the gas forging heating furnace also has good heat loss control ability and intelligent control system, which can accurately adjust the ratio of air to natural gas, ensure full combustion of natural gas, and reduce mechanical incomplete combustion and chemical incomplete combustion.、Uniform heating and precise control can be realized, so it is helpful to improve the product quality and yield of metal materials.、Adopting advanced combustion technology and materials, it has a long service life and low maintenance cost.、Usually equipped with intelligent control system, it can automatically adjust the parameters such as gas supply and air flow according to the heating demand, and realize accurate control of the temperature and atmosphere in the furnace.、Adopting advanced combustion technology and control system can realize full combustion of natural gas and improve combustion efficiency. At the same time, some equipment is also equipped with waste heat recovery system, which can further recycle the waste heat in exhaust smoke and improve energy utilization efficiency.，be loved by our customers.。

1、Brief introduction of High temperature bright well annealing furnace

High temperature bright well annealing furnaceIt is an important heating equipment before metal forging. It uses natural gas as fuel to heat metal materials through high-temperature flame and smoke generated by combustion to meet the requirements of forging process.，the main features are energy saving and environmental protection, Easy to control, Strong adaptability, energy-efficient and energy saving and environmental protection。

High temperature bright well annealing furnace

2、High temperature bright well annealing furnace performance advantage

The advantages of High temperature bright well annealing furnace are as follows:

1. Wide application range

The High temperature bright well annealing furnace is suitable for forging and heating of various metal materials, including steel, aluminum and copper. At the same time, it can also be used in metal heat treatment, tempering and other technological processes.

2. easy to operate

The operation interface of the High temperature bright well annealing furnace is friendly and easy for operators to use. At the same time, the equipment also has the function of fault diagnosis and alarm, which can find and deal with abnormal situations in time.

3. Rapid temperature rise

The High temperature bright well annealing furnace can heat the metal material to the required temperature in a short time, which improves the production efficiency.

4. Improve product quality

Because the High temperature bright well annealing furnace can realize uniform heating and precise control, it is helpful to improve the product quality and yield of metal materials.

5. Uniform heating

The High temperature bright well annealing furnace adopts regenerative combustion system or advanced burner design, which can realize uniform distribution of temperature in the furnace, ensure uniform heating of metal materials and improve product quality.

High temperature bright well annealing furnace

3、High temperature bright well annealing furnace use

The purpose of High temperature bright well annealing furnace is introduced as follows:

1. Metal melting and casting

Although it is mainly used for forging heating, some types of High temperature bright well annealing furnaces can also be used in metal melting and casting processes. This is especially suitable for melting and casting of small or special alloys.

2. Metal forging heating

The High temperature bright well annealing furnace can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

3. Metal tempering

By properly heating and cooling the metal material, the High temperature bright well annealing furnace can realize the quenching and tempering treatment of the metal. This is helpful to adjust the hardness and toughness of metal to meet the needs of different workpieces.

4. Energy conservation and environmental protection

The High temperature bright well annealing furnace uses clean energy as fuel, which has lower emissions and higher energy efficiency than traditional coal-fired or oil-fired stoves. This is helpful to reduce environmental pollution and realize green production.

5. Metal forging heating

The High temperature bright well annealing furnace can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

High temperature bright well annealing furnace

4、High temperature bright well annealing furnace function

High temperature bright well annealing furnacemultifunctional, with functions such as temper, Forging heating, Casting heating, Forging heating and hardening and tempering，the advantage is It can improve the plasticity and fluidity of metal materials, reduce the difficulty and cost of forging, and improve product quality and production efficiency.、Efficient combustion and waste heat recovery system can significantly reduce energy consumption, thus reducing operating costs.、Using regenerative combustion system or advanced burner design can realize the uniform distribution of temperature in the furnace, ensure the uniform heating of metal materials and improve product quality.、Usually equipped with intelligent control system, it can automatically adjust the parameters such as gas supply and air flow according to the heating demand, and realize accurate control of the temperature and atmosphere in the furnace.、It has the advantages of high heating efficiency, high energy utilization, accurate temperature control, good environmental protection performance, simple operation and strong adaptability.，it has the characteristics of energy-efficient, Stable and reliable, Easy to maintain, Easy to control and Strong adaptability，was developed and designed by One-combustion energy saving。

High temperature bright well annealing furnace

5、High temperature bright well annealing furnace HD real shot

On-site aerial photography of High temperature bright well annealing furnace。

High temperature bright well annealing furnace

As you can see from the live video.，One-combustion energy saving It is a product series that integrates Metal tempering, Energy conservation and environmental protection, Energy conservation and environmental protection, Metal melting and casting and Metal forging heating。

6、High temperature bright well annealing furnace function

High temperature bright well annealing furnaceit has the functions of anneal, normalizing, quench, temper and heat treatment，is a kind of High temperature bright well annealing furnace manufactured by One-combustion energy saving。

High temperature bright well annealing furnace

High temperature bright well annealing furnaceat runtime,Heat of combustion based on fuel. Natural gas is sprayed from the burner, mixed with combustion-supporting air and burned to produce high-temperature flame and smoke. These high-temperature flames and smoke transfer heat to the metal materials in the furnace by radiation and convection, so that they gradually heat up to the temperature required for forging.，widely used inchemical industry,material,aerospace,Household necessities,machinery and other industries。