What is a Dual heat storage walking back and forth furnace? Introduction to the advantages and characteristics of the Forging furnace

Dual heat storage walking back and forth furnaceIt is a kind of equipment that uses natural gas as fuel to heat metal materials and make them reach forging temperature.。

1、Brief introduction of Dual heat storage walking back and forth furnace

Dual heat storage walking back and forth furnaceIt is a forging heating device using gas as fuel.，Natural gas is used as a heat source, resulting in less waste gas and smoke after combustion, and less pollution to the environment. This will help reduce industrial emissions and improve the atmospheric environment.、Adopting advanced combustion technology and materials, it has a long service life and low maintenance cost.、Adopting advanced combustion technology and control system can realize full combustion of natural gas and improve combustion efficiency. At the same time, some equipment is also equipped with waste heat recovery system, which can further recycle the waste heat in exhaust smoke and improve energy utilization efficiency.、The metal material can be heated to the required temperature in a short time, and the production efficiency is improved.、It has the advantages of high heating efficiency, high energy utilization, accurate temperature control, good environmental protection performance, simple operation and strong adaptability.，multifunctional, with functions such as heat treatment, temper, normalizing, temper and heat treatment，reliable quality。

Dual heat storage walking back and forth furnace

2、Dual heat storage walking back and forth furnace use

The purpose of Dual heat storage walking back and forth furnace is introduced as follows:

1. Energy conservation and environmental protection

The Dual heat storage walking back and forth furnace uses clean energy as fuel, which has lower emissions and higher energy efficiency than traditional coal-fired or oil-fired stoves. This is helpful to reduce environmental pollution and realize green production.

2. Metal forging heating

The Dual heat storage walking back and forth furnace can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

3. Improve production efficiency

The Dual heat storage walking back and forth furnace has the advantages of fast heating speed and accurate temperature control, which can improve production efficiency. This is especially important for mass-produced forging workshops.

4. Metal melting and casting

Although it is mainly used for forging heating, some types of Dual heat storage walking back and forth furnaces can also be used in metal melting and casting processes. This is especially suitable for melting and casting of small or special alloys.

5. Metal heat treatment

In addition to forging heating, Dual heat storage walking back and forth furnaces can also be used for metal heat treatment processes, such as annealing and tempering. These processes can improve the microstructure and properties of metal materials, and improve their service life and mechanical properties.

Dual heat storage walking back and forth furnace

3、Dual heat storage walking back and forth furnace structure composition

The Dual heat storage walking back and forth furnace structure is introduced as follows:

1. ventilation system

Ensure the gas flow in the furnace and maintain the stability of the atmosphere and temperature in the furnace.

2. combustor

The device that mixes natural gas with combustion-supporting air and ejects it is the core component of the heating furnace.

3. Radiation chamber

The heat load of the main place for Dual heat storage walking back and forth furnace heat exchange accounts for about 70%-80% of the whole furnace. The furnace tube in the radiation room conducts heat through flame or high-temperature flue gas, which is mainly radiant heat, so it is called radiation tube.

4. convection chamber

The material is heated by convection heat transfer of high temperature flue gas discharged from the radiation chamber. Flue gas washes the tube wall of the furnace tube at a high speed to carry out effective convection heat transfer, and its heat load accounts for about 20%-30% of the whole furnace. The convection chamber is generally arranged above the radiation chamber, and some are placed on the ground alone. In order to improve the heat transfer effect, nail head tubes or finned tubes are often used in furnace tubes.

5. Waste heat recovery system

Used to recover the exhaust heat of the heating furnace. There are two kinds of recovery methods, one is to recover by preheating combustion air, so that the recovered heat can return to the furnace again; The other is to use another recovery system to recover heat. The former is called air preheating mode, and the latter is usually called waste heat boiler mode.

Dual heat storage walking back and forth furnace

4、Dual heat storage walking back and forth furnace function

Dual heat storage walking back and forth furnacemultifunctional, with functions such as Casting heating, normalizing, anneal, quench and hardening and tempering，It has a wide range of uses, and is often used inMetal heat treatment,Metal melting and casting,Metal forging heating,Metal heat treatment,Metal tempering and so on，be loved by our customers.。

Dual heat storage walking back and forth furnace

5、Dual heat storage walking back and forth furnace use

The purpose of Dual heat storage walking back and forth furnace is introduced as follows:

1. Metal tempering

By properly heating and cooling the metal material, the Dual heat storage walking back and forth furnace can realize the quenching and tempering treatment of the metal. This is helpful to adjust the hardness and toughness of metal to meet the needs of different workpieces.

2. Energy conservation and environmental protection

The Dual heat storage walking back and forth furnace uses clean energy as fuel, which has lower emissions and higher energy efficiency than traditional coal-fired or oil-fired stoves. This is helpful to reduce environmental pollution and realize green production.

3. Improve production efficiency

The Dual heat storage walking back and forth furnace has the advantages of fast heating speed and accurate temperature control, which can improve production efficiency. This is especially important for mass-produced forging workshops.

4. Metal melting and casting

Although it is mainly used for forging heating, some types of Dual heat storage walking back and forth furnaces can also be used in metal melting and casting processes. This is especially suitable for melting and casting of small or special alloys.

5. Metal tempering

By properly heating and cooling the metal material, the Dual heat storage walking back and forth furnace can realize the quenching and tempering treatment of the metal. This is helpful to adjust the hardness and toughness of metal to meet the needs of different workpieces.

Dual heat storage walking back and forth furnace

6、Why choose One-combustion energy saving?

Choosing a suitable Dual heat storage walking back and forth furnace manufacturer requires comprehensive consideration of many aspects. First of all, we should examine the strength of manufacturers, including production capacity, R&D team and industry experience. Strong manufacturers can better ensure product supply and innovation ability. Secondly, product quality is the key, and it is evaluated by product certification, material selection and manufacturing process to ensure the durability of products. Product performance can not be ignored, so we should choose manufacturers with matching technical parameters, rich types and customized services according to actual needs. After-sales service is equally important. Professional and timely service team, perfect after-sales content and extensive service network can make users worry about nothing. In addition, market reputation is also an important reference. We can understand the reputation and status of manufacturers through customer evaluation, industry reputation and award-winning honor. Finally, it is necessary to analyze the price and cost performance, and on the premise of ensuring the quality and performance, choose a manufacturer with reasonable price and high cost performance, so as to purchase Dual heat storage walking back and forth furnace products that meet the demand and have good cost performance.。

One-combustion energy saving

Dual heat storage walking back and forth furnaceis a kind of high quality and low price Dual heat storage walking back and forth furnace，at the start of the operation,Heat of combustion based on fuel. Fuel gas (such as natural gas, liquefied petroleum gas, etc.) is mixed with combustion-supporting air through the burner and burned to produce high-temperature flame and flue gas. These high-temperature flames and smoke exchange heat with metal materials in the furnace, so that they gradually heat up to the temperature required for forging.。